Replies to This Discussion

Permalink Reply by Ron "Oily" Sprague on February 26, 2012 at 6:05am

Dave,

Make it easy on yourself: 6-5-4 strings from a standard six string set ( that's E-A-D, tuning the A up to B, and the D up to E). Should work fine.

• ▶ Reply

Permalink Reply by Dan Sleep on February 26, 2012 at 6:06am

What Oily said....

• ▶ Reply

Permalink Reply by Ron "Oily" Sprague on February 26, 2012 at 6:05am

Oh, and use Medium gauge.

• ▶ Reply

Permalink Reply by Dan Sleep on February 26, 2012 at 6:06am

That too...

• ▶ Reply

Permalink Reply by Dave Hall on February 26, 2012 at 6:16am

Thanks Guys.

I did not want to appear a bit thick, but now a least I will sleep tonight !!

Cheers,

Dave

• ▶ Reply

Permalink Reply by Keni Lee Burgess on February 26, 2012 at 8:18am

Hey Dave,

Just be careful with those higher tunings. Hopefully the neck is thick or better yet contains a truss rod.

EBE puts a lot of stress on a neck. 

Tuning DAD and using a capo on fret 2 is a lot better. Same standard strings EAD (tune down).

I prefer using strings AGD and tuning down to GDG. Although of course, this puts me in the key of G.

Enjoy, Keni Lee  

• ▶ Reply

Permalink Reply by Ron "Oily" Sprague on February 26, 2012 at 8:28am

See? Keni kicks in with a better way! Thanks, man!

• ▶ Reply

Permalink Reply by The Phrygian Kid on February 26, 2012 at 10:56am

No one asking about ur scale length..
Interesting...
Impossible tO answer without knowing the length of your strings.

Ps using lighter strings is a double edged thing, heavier sounds better.
Ps2 I never seen a three string that needed a truss rod ever
I do a 600mm scale length and have no trouble cranking a low e string up to g

• ▶ Reply

Permalink Reply by Dave Hall on February 26, 2012 at 1:11pm

In repy to Keni's comment.

It will be a through neck made fron 2"x1" Beech.

Hopfully that will be strong enough.

I have used 4-5-6 strings tuned to open G on another guitar,

that had an Oak neck with no problems.

So hopefully this will be OK.

Dave

• ▶ Reply

Permalink Reply by jason fitzgibbons on February 26, 2012 at 2:11pm

just finished two three stringers, one with a maple neck with an oak fretboard, and one mahogany neck with poplar fretboard.  both are tuned ebe with the three thickest strings from a light gauge set.  the both hold great and sound good. oh and one scale is 24, and one is 24.25.  i will post pics and vids soon

• ▶ Reply

Permalink Reply by Dave Hall on February 26, 2012 at 2:19pm

Cheers Jason,

I think light gauge is the way to go

Dave

• ▶ Reply

Permalink Reply by Keni Lee Burgess on February 27, 2012 at 3:08am

Yes, scale length is definitely a consideration. Even on a standard 6 string with a truss rod, I would not advise leaving a guitar tuned up above standard. Due to the fact there is no standard in regards to any of the CBG's dimensions, approaching a tuning in a relative way might be a good consideration. If you are not overly concerned with the key, experimenting could easily lead to the guitar playing at it's best. For example: If you use strings EAD start by tuning CGC...C#G#C#...DAD...D#A#D#...EBE...Simply moving up in pitch using tones 151 from the major scale.

If the strings are too tight or too loose the sound board will not vibrate correctly.

You may discover in this way, what string tension functions best.

Enjoy, Keni Lee   

• ▶ Reply

• ‹ Previous
• 1
• 2
• Next ›
• Page