Hi All,

Well the Deco build is almost complete but have a hum and dont know if its dodgey soldering (I have de-soldered my last effort & resoldered) or do I need to shield it (single coil pick-up & piezo with blender pot.

Any tips on how to figure out which is the more likely -  would be of assistance.

The hum is there as soon as I plug in and seems to be in the medium to higher frequences.

Views: 753

Reply to This

Replies to This Discussion

Case the pot only or should I case the PUP as well?

Artist Formerly Known as Matt said:

I would shield the pup. Just for info, the first thing I always do with new basses is too remove the pick guard and add shielding.

I assume you have a ground going to the case of the pot?

Since you have what looks like a stacked pot, the volume part needs to be grounded to the case.

You might also want to ground the pot case to the jack , in fact , might wanna try that first.

 

 

 

AFKAM

Grounding the pot to the jack wouldnt cause a ground loop? 

Artist Formerly Known as Matt said:

I would shield the pup. Just for info, the first thing I always do with new basses is too remove the pick guard and add shielding.

I assume you have a ground going to the case of the pot?

Since you have what looks like a stacked pot, the volume part needs to be grounded to the case.

You might also want to ground the pot case to the jack , in fact , might wanna try that first.

 

 

 

AFKAM

K. So long as what we are seeing is like:

 

 

you're ok.

 

-WY

Nah if you connect to the 'ring' or 'sleeve' part of the jack -- not the part that touches the tip end.

 

-WY


Penny Nelson said:

Grounding the pot to the jack wouldnt cause a ground loop? 

Artist Formerly Known as Matt said:

I would shield the pup. Just for info, the first thing I always do with new basses is too remove the pick guard and add shielding.

I assume you have a ground going to the case of the pot?

Since you have what looks like a stacked pot, the volume part needs to be grounded to the case.

You might also want to ground the pot case to the jack , in fact , might wanna try that first.

 

 

 

AFKAM

A ground loop is created any time the signal can take multiple paths to the ground on the jack.

 

Typically you will attach all ground wires to the case of one of the pots, then run a wire from the case where all the grounds are to the ground on the jack. The ground can only have one route to take.

 

If you run multiple ground wires to multiple locations, you can inadvertently cause a ground loop, which could cause a hum.



Penny Nelson said:

Grounding the pot to the jack wouldnt cause a ground loop? 

Artist Formerly Known as Matt said:

I would shield the pup. Just for info, the first thing I always do with new basses is too remove the pick guard and add shielding.

I assume you have a ground going to the case of the pot?

Since you have what looks like a stacked pot, the volume part needs to be grounded to the case.

You might also want to ground the pot case to the jack , in fact , might wanna try that first.

 

 

 

AFKAM

Penny,

One question about your first pic in the sequence: is that the rod piezo, sitting behind the saddle, and next to the strings? If so, it appears from the pic that all your strings are actually touching it. You may already know this, but the best placement for a rod piezo ( I have installed two of these on classical guitars over the years, my Ovations are set up the same way - actually, the rod piezo is molded directly into the saddles on the Ovations - and my newish Yamaha FGX720SCA is exactly like what I am about to describe) is directly underneath the saddle. In many commercial guitars, the rod is set in a shallow slot in the bridge, and the saddle slots in directly atop that.

If that is indeed the piezo rod just behind the saddle and touching the strings, you need to put it beneath the saddle, not touching the strings. This may be the source of your hum. However, in looking at your wiring, I also think Wes may be right: it just somehow looks like there might be a ground loop in there as well.

Hope this helps,

Oily
Penny,

Further to my last, I now suspect that what I'm seeing in your pic #1 is your metal skewer grounding apparatus. Rats...

Oily
Yes, it is my dodgey grounding apparatus.  Yep I put the piezo under the bridge like real acoustic/electric guitars. with a camel bone compensated bridge. It has all the bells and whistles... and a hum lol.  Going to build a box for the pot & pick up tonight and shield it. Failing that I will run the ground back to the equaliser and see if that sorts it.. because whilst its not bad now it does lessen more if I touch the strings... will keep you all posted on the results... cant wait till I can make a sound file for you all. Appart from the hum it sounds awesome!!

oh okay I have them all to the pot but not back to the jack will try that as well.
Dan Sleep said:

A ground loop is created any time the signal can take multiple paths to the ground on the jack.

 

Typically you will attach all ground wires to the case of one of the pots, then run a wire from the case where all the grounds are to the ground on the jack. The ground can only have one route to take.

 

If you run multiple ground wires to multiple locations, you can inadvertently cause a ground loop, which could cause a hum.



Penny Nelson said:

Grounding the pot to the jack wouldnt cause a ground loop? 

Artist Formerly Known as Matt said:

I would shield the pup. Just for info, the first thing I always do with new basses is too remove the pick guard and add shielding.

I assume you have a ground going to the case of the pot?

Since you have what looks like a stacked pot, the volume part needs to be grounded to the case.

You might also want to ground the pot case to the jack , in fact , might wanna try that first.

 

 

 

AFKAM

we are okay then :D on that count anyway


Wes "Moaning Mule" Yates said:

K. So long as what we are seeing is like:

 

 

you're ok.

 

-WY

okay! Thanks for all your help seems like its sorted now. Solution shielded both pick up and pot separately. ran earth wire from shielding to back of pot ran earth wire to jack. 

Thanks again everyone - now I can move on to the next error in judgement acoustic bridge with no tailpiece for strings - box bowed and strings to high at 12 fret so am going to get a hinge or something for tail piece to take teh stress of the soundboard and reinforce the base of the box....tomorrow night after work...lol

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

crossover guitar.

Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Mar 21. 11 Replies

Tune up songs

Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies

Duel output jacks

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies

How to Get Your Own Music on Spotify

Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray Feb 21. 2 Replies

CB Bass Guitar

Started by Mi Rankin in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Jan 27. 5 Replies

Latest Activity

A.D.EKER commented on Dar Stellabotta's video
Thumbnail

A Cigar Box Guitar Six Stringer Built by Louie Lamanna

"i See Your ready to Blow away the GRAND STADIUM ! tree strings more of DAR DELIGHT !! Shine Girl !…"
4 hours ago
A.D.EKER commented on A.D.EKER's video
Thumbnail

Im Troubled (Tribute) Mc K Morganfield by BCB - A.D .Eker 2024.

"Thank you for the kind comments Doug! Glad you liked the Picture !"
4 hours ago
BrianQ. commented on Dar Stellabotta's video
9 hours ago
BrianQ. liked Dar Stellabotta's video
9 hours ago
Southern Ray commented on Southern Ray's photo
Thumbnail

Project Punch!

" Thank ya again Keith!"
11 hours ago
Southern Ray commented on Southern Ray's photo
Thumbnail

Punch Project!

" Thank Ya Keith!"
11 hours ago
Doug Thorsvik commented on AGP #'s photo
Thumbnail

AGP #527 - ''Led-Zep 2''

"This build really strung you along Alan! Reminded me of all my fishing line experiments; a lot of…"
13 hours ago
Doug Thorsvik commented on A.D.EKER's video
Thumbnail

Im Troubled (Tribute) Mc K Morganfield by BCB - A.D .Eker 2024.

"Diggin’ the slow blues. I like that last pic Andries! Look at all those cool guitars. Yeah!!!"
13 hours ago
Dar Stellabotta posted a video

A Cigar Box Guitar Six Stringer Built by Louie Lamanna

This video is the unboxing and the demonstration of a beautiful, six stringer built by Louie Lamanna. Join Louie and I June 15 at the second annual Pittsburg...
14 hours ago
Doug Thorsvik commented on Doug Thorsvik's video
Thumbnail

Hail the Resurrection Day: 2-String Violin Chugger Cigar Box Guitar

"Happy Easter to you too Andries! The passion is definitely in full swing. Turns out I’m…"
15 hours ago
A.D.EKER commented on Doug Thorsvik's video
Thumbnail

Hail the Resurrection Day: 2-String Violin Chugger Cigar Box Guitar

"Happy Easter Doug ! the Passion is in full swing !"
15 hours ago
A.D.EKER commented on Ricky D's photo
15 hours ago

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->