Pretty self explanetory, my ruby amp starts motorboating when I turn up the volume.  The setup is crammed inside a small speaker cabinet, and the pc board is fully soldered but the rest of the connections (volume pot...) are all with alligator clips since I can't drill through the box yet.

(motorboating is where it's like a continuous ocatve effect, right? cause that's what it's doing)

Views: 604

Replies to This Discussion

Don't turn it up so loud.

 

No, seriously, which pot are you turning up?  Sounds like you might have a feedback loop where there should not be one, OR the input level coming in to the ruby amp is way too hot. 

 

Disclaimer:  I've never debugged a ruby amp, specifically, but based on some other similar amps I've worked on those are the first few things I would try.

i don't know the ruby amp, but have built several valve amps...

but motorboating is not an octave type effect.  it's a low frequency oscillation - like putt-putt-putt.

the octave type effect you mention, i have heard of on modded tube screamers etc. caused by changes to the feedback/clipping circuit.

have you swapped out your IC? not all chips are created equal, and for a buck a piece, it's good to have a few kicking around to try.

also maybe check your voltages right at the IC pins, just to make sure the chip is getting the power it needs to work properly, just a thought.

 

I deleted my reply. But it seems you can only edit. So please ignore this post.

sorry!

I just spent a little bit of time debugging it and I figured out what was wrong.

 

My crappy soldering job created shorts when I crammed it in the cabinet.  I fixed it up and I can get it  to work well but whenever I move the components it starts oscillating (not motorboating) like crazy.  I haven't  been able to test it really well (which component movement creates the oscillations) since I don't wanna bust the LM386 because it's soldered in place (no socket, facepalm). It doesn't seem like anything would be microphonic, but I've heard bad vacuum tubes can become microphonic, but this is solid state. Keep in mind when I had it on a breadboard I stuffed it in a box to test different speakers and it worked perfectly.

Can you post some pictures? Perhaps we can see what goes wrong.
Alright, some more debugging

moved the 9 volt battery closer to the pcb, no change, works perfectly.

same with speaker

same with control panel (plank of wood with pots and jack and switch on it (when I moved I got a tiny quiet little clickish type thing then some hum, then I moved it a bit more and it was fine))

But then, I move the pcb, eeeeeeeeeeeeeeeeeeeeeeeeevvvvvvvvvvvvvvvvvvzzzzzzzzzzzzzzzzzzzzzzzzzzzzrrrrrrrrrrggggggggghhhhhhhhhh (oscillations)

I think it might be the LM386 that I stupidly soldered in place. I dropped and it might have knocked something loose but I don't know if that can damage it. I'll try and get a video soon.
Sounds like a short or bad connection. Check all your solder joints on the pcb. Make sure no shorts between tracks. Maybe reheat every joint to assure it is connected right.
I wonder if the LM386 doesn't have an overload protection circuit that might be clipping the output.  Maybe the amp wants a different speaker?
You can connect ANY speaker to a Ruby. It will however sound best with an 8 ohm. You can even connect a Marshall 4x12 cab without problems (I did!).

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Discussion Forum

Ruby Amp

Started by BrianQ.. Last reply by BrianQ. May 18, 2020. 6 Replies

Smokin' amp (literally)

Started by James Conder. Last reply by James Conder Aug 27, 2019. 4 Replies

Simple Headphone/Practice Amp

Started by BrianQ. May 16, 2019. 0 Replies

Problem with second-hand amp.

Started by Arthur Payne Mar 31, 2019. 0 Replies

Artec Amp Help!

Started by Jesse Lively Sep 10, 2017. 0 Replies

LM386 N-4

Started by Denis U. Last reply by Richard Haas Dec 3, 2016. 4 Replies

History Mystery--Orrtronic Tube Amplifier project

Started by Scott aka Farmer Ted Nov 17, 2016. 0 Replies

Dual IM386 Chip amp

Started by Paul Craig. Last reply by Paul Craig Nov 3, 2016. 31 Replies

Amp Speakers

Started by Primitive Acoustics. Last reply by Primitive Acoustics Mar 9, 2016. 3 Replies

Grounding for Cigar Box Amps: Chassis Ground?

Started by Erik Bell. Last reply by Scott aka Farmer Ted Dec 20, 2015. 4 Replies

Neat amp components

Started by Surly. Last reply by Alan Steeg Oct 27, 2015. 1 Reply

can a dab radio be turned into an amp

Started by Coventry Halfpenny guitars. Last reply by Pickedmoor Jon Oct 20, 2015. 3 Replies

SDA-T Questions

Started by alectron. Last reply by Zac Ray Sep 2, 2015. 10 Replies

HI - New guy & And speaker question

Started by Henry S. Last reply by Henry S Mar 25, 2015. 4 Replies

Are Pre-fabbed LM386 Moduals Worth Trying?

Started by Scott W. Last reply by Henry S Mar 24, 2015. 6 Replies

Powered sub to amp ??

Started by wormil. Last reply by wormil Sep 2, 2014. 2 Replies

Amp and speaker INSIDE the guitar?

Started by Greg Potts. Last reply by Ron "Oily" Sprague Jul 1, 2014. 1 Reply

trying to hack an old valve radio, into a guitar amp,

Started by GARAGE HERMIT. Last reply by GARAGE HERMIT Apr 29, 2014. 108 Replies

Best mini amp KITS

Started by MichaelS Country Boy Guitars. Last reply by Henrik Johansson Mar 10, 2014. 34 Replies

amp wiring help

Started by HarleyTodd. Last reply by Bernie Mango Feb 26, 2014. 18 Replies

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->