Long time guitar player here, but I'm mostly an electric bass player these days.  Anyway, someone posted a link to a Samatha Fish video on the TalkBass forum a couple of weeks ago.  That put a burr under my saddle re- CBG.  I have a tad of building experience, I made two electric bass guitar bodies last year.  Paired with bolt-on commercial necks, that was fine and worked well. 

Anyway, low and behold last week at the community garden, there's a wooden cigar box sitting on the "Free" shelf.  The guitar gods had spoken, apparently. 

Anyway, I snagged it and used the community shop CNC laser to burn an F-hole in it yesterday.  Soaked some hardware from the junk box in vinegar night before last to age it.  That worked well.  Next up -  hunting for neck wood.  I think I'll buy a pre-slotted fretboard to epoxy to the neck. 

 

Views: 520

Reply to This

Replies to This Discussion

Re- neck angle.  Yes - I cut an extra 1/4" off the TOP of the tail of the neck, so the neck is tilted back.  Means that the tail support is 1/4" higher than the other one.   I didn't explain it well in my previous post.  You can kinda see it in the image. 

Big day in the shop. 

-Bad news first.  Walnut supports must have shifted up slightly when clamped/glued.  With almost no tolerance, now the box won't close properly.  Some dremel work fixed that.  Then the neck heel  needed some belt sander touchup, since it was sitting higher also.

-Neck drilled for screws.  Temporarily attached and tailpiece location confirmed using string.  Action looks acceptable.  

-Walnut block prepared to use under the strikeplate tailpiece.  Problem is the strikeplate screws aren't going to hit much wood.  With the wider walnut, I can screw it into the meat of the box.

-Tail ground wire installed and tested. 

-Walnut patch prepared to go in spot where FB doesn't quite reach the box top. 

-Control plate isn't going to work.  There's just not enough 'real estate' on the box top to have both pots and the input. The upper pot is too close to where the bridge will be.   I need to go side of the box with the input and move the pots to horizontal. 

Takes a good bit of planning to get all the components to fit.  I sometimes leave out the tone control.

Sure wish I could cut out an F-hole that nice!

Turns out the pot shafts are long enough to go directly through the top.  I can always add a plate later.

I hear you on the tone.  Without it, leaves more space.  And it's likely rarely changed.  But, not knowing how this will sound, I wanted to include it.  

  

There are other ways to change the tone without using a tone pot.  ;)

Hi, good to follow your progress, warts and all, Haha.

Not only different ways to get tone, from the amp, from a pedal, or multiple pickups but also different places to mount and extra pots.

Here are a couple of ideas I have used. Tone and volume on the side keep the top free of stuff.

Guitar on right has pots in the top side This guitar has volume disguised under a dummy sound hole cover and tone on the tail end.

Taff

Cool, thanks for sharing.  I thought about moving one or both.  I didn't want them on the bottom for 'sit-ability' and my ends are too thick. 

Re - pickup location.  I know from my old guitar days that I prefer a neck pickup.  Bridge is too trebly.  I measured my P-basses.  On them the P/U is 85% of the scale length from the nut.  So, on a 25.5" scale, that puts the P/U at approximately 21.5" from the nut.  I'm using a flat bucker, so I can blue tape it down and move it around for a while. 

Getting close. 

-P/U mounted.  Soldering done.  Drilled out and mounted jack plate.  "Click" tested with headphone amp. 

-Partially finished the bridge. It's 7/8" high which is probably at least a 1/4" too tall. 

-Glued a walnut scrap on the underside of the neck between the box supports, just to beef it up.  That glue needs to dry overnight before I tension it with strings.

-Finished the walnut piece to fit between the FB and box.  It looked like a bad patch job when oiled, so I stained it black.  Looks better to me. 

-Four knob options. two shown here.  Halves of a wine stopper.  I beefed the hole up by dripping CA into it.  Others are copper end caps that I filled with epoxy.  Also have some turned ones from Oak and some plastic OEM Yamaha ones.  

Been a blast.   

Plugged it in yesterday and started plinking around.  The humbucker in the neck position with the tone rolled all the way off (heavy electric strings) sounds great through my Ampeg bass amp.  My wife walks in all google eyed and states "At works!".   Made a temporary bridge out of a dowel with a craft stick under it.  Need to get to the belt sander at the shop and take the bridge height down. 

Taff,

Using the dummy sound hole cover was a really slick idea. Very cool look.

Hi Lane, thanks for the comment. I've posted a "how to do it" on here.

Taff

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

crossover guitar.

Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Mar 21. 11 Replies

Tune up songs

Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies

Duel output jacks

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies

How to Get Your Own Music on Spotify

Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray Feb 21. 2 Replies

CB Bass Guitar

Started by Mi Rankin in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Jan 27. 5 Replies

Latest Activity

A.D.EKER commented on A.D.EKER's video
Thumbnail

Im Troubled (Tribute) Mc K Morganfield by BCB - A.D .Eker 2024.

"Thank you Poorness ! for loving it ! appreciated!"
11 hours ago
Southern Ray replied to Timothy Hunter's discussion just came accross this pickup idea on youtube.
" Very interesting. Thank you Timothy!"
11 hours ago
Kent Thurston updated their profile
12 hours ago
Southern Ray posted a photo

Punch Project!

She now sports gold metal CBGitty knobs, speaker and an Artec 2.5 watt speaker. Finished this in…
12 hours ago
Southern Ray posted a photo

Project Punch!

Gonna finally get back on this long-delayed project that is more than half complete. (The matching…
13 hours ago
Poorness Studios liked A.D.EKER's video
15 hours ago
BrianQ. left a comment for Rob (Uker) Porras
"Hope this helps?"
15 hours ago
Doug Thorsvik commented on Doug Thorsvik's photo
Thumbnail

Dueling Flatheads

"I appreciate the kind words Papa D! I have always loved the look of these cigar boxes. Glad to have…"
17 hours ago
A.D.EKER commented on A.D.EKER's video
21 hours ago
A.D.EKER posted a video

Im Troubled (Tribute) Mc K Morganfield by BCB - A.D .Eker 2024.

The recorded History By Alan Lomax for the library of Congres of the Blues, from Mc Kinley Morganfield (Aka Muddy Waters) the in this take recorded Tribute ...
21 hours ago
Papa D commented on Doug Thorsvik's photo
Thumbnail

Dueling Flatheads

"Beautiful..Nice work Doug.."
yesterday
Papa D commented on Papa D's photo
Thumbnail

american1 Sun Glo

"Thanx AGP & Doug..  4 more coming soon"
yesterday

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->