Replies to This Discussion

Permalink Reply by Robbie on April 13, 2018 at 2:48pm

Yep! And that is what I was saying about thin body cigar boxes. Bottom loading...

• ▶ Reply

Permalink Reply by Robbie on April 13, 2018 at 2:59pm

Thank you. A picture says a thousand words eh? :)

• ▶ Reply

Permalink Reply by Korrigan on April 13, 2018 at 2:40am

You can also drill new string holes so you can string it from the front. 

• ▶ Reply

Permalink Reply by Taffy Evans on April 13, 2018 at 9:37am

Hi, if it's an electric guitar then then it's not so important that the bridge sits in the sweet spot of the top. I would put a block of wood up against the tail end of the box between top and back, and screw through the top into the block. The neck would be moved to a position at the other end to get correct scale length.

You can buy ferrels to seat the string "balls" into on the back.

Taff

• ▶ Reply

Permalink Reply by Robbie on April 13, 2018 at 2:42pm

I thank you all...What I get from here and what I think is right, Is at the point of stings going thru they should go through the bottom and the while neck thru to the bridge right?

• ▶ Reply

Permalink Reply by Robbie on April 13, 2018 at 2:50pm

:) that's sounds simple....Thank you

• ▶ Reply

Permalink Reply by Robbie on April 13, 2018 at 2:55pm

Yes....Kinda sorta. I'm installing a Snake Bite Mini Humbucker towards the neck position. I will have a 1/4 " fretboard ,

• ▶ Reply

Permalink Reply by Robbie on April 13, 2018 at 3:04pm

Thank you

• ▶ Reply

Permalink Reply by Cause the Blue rat on April 15, 2018 at 9:25am

You could always drill through the bridge's back. Get a very small drill bit. Meant for cutting through steal. Just has to be wide enough to accommodate the string. Some cutting or motor oil. Take the bridge apart. Clamp it so the end is facing up. Drill to the bottom of each saddle screw hole on the back by first. Putting oil on the steal. Drilling slowly and make sure to stop and re oil. The oil will keep the drill bit from heating up. You want to go slowly and keep the bit cool so you don't break the bit. After drilling clean up the oil and re assemble the bridge. 

The oil will go all over the place so make sure to wear work clothing. And cover anything around the drilling area to keep it clean as well. The floor is going to get splatters as well. Good idea to remember to clean that up too. 

To get an idea of where to drill the string holes just look at actions on Ebay for 'strat stoptail' bridges. Find one with pictures of the back of the bridge. 

Attachments:

• s-l1600-11.jpg, 69 KB

• ▶ Reply

Permalink Reply by Korrigan on April 15, 2018 at 11:19am

I must live dangerously, I don't take it apart, clamp it, or use oil.  :D

Though using a cheap zinc allow tailpiece is probably why it's so easy. A steel tailpiece would definitely take more care.

• ▶ Reply

Permalink Reply by Cause the Blue rat on April 20, 2018 at 3:50pm

Sorry Korrigan. I didn't read through the posts before I posted. Just jumped right in the mix. 

and by the way, GREAT idea Korrigan! This saves the hassle of lining all those string holes up. 

• ▶ Reply

Permalink Reply by Korrigan on April 20, 2018 at 5:23pm

Thanks, but my spelling isn't so great, I meant to type zinc alloy. lol

• ▶ Reply

• ‹ Previous
• 1
• 2
• Next ›
• Page