Replies to This Discussion

Permalink Reply by darryl kernaghan on December 2, 2017 at 3:18am

That is a cool looking box Paul, I'd try it un thinned 1st, you might be surprised, but if you do chose to thin it, leave all the edges full thickness, and just relieve it in between load areas, leaving thickness where bracing might be if you were making a box, I really hope you can get rid of the marker ink neatly

• ▶ Reply

Permalink Reply by Paul Cezanne on December 2, 2017 at 3:47am

Thanks! I'll go for it and see what happens. And yes, if it needs thinning I'll leave a strong edge.

I'm really liking the marker ink, I name things (instruments, cars, kayaks...) this one will be named Copper Tubing!

• ▶ Reply

Permalink Reply by MadGomer on December 2, 2017 at 3:59am

I'd bet you're going to be happy with that as is, I certainly wouldn't thin it out at this point. Love the character of that box!

• ▶ Reply

Permalink Reply by Paul Cezanne on December 2, 2017 at 4:10am

Interesting, I had planed on a pickup, the thin rod piezo kind. It's already on it's way. LOL. But i guess I can try first. I had planned on making it both acoustic and electric so I can get that Blues sound.

Love the whisky box!

• ▶ Reply

Permalink Reply by MadGomer on December 2, 2017 at 4:13am

Nothing wrong with a rod piezo, you just need a small hole for the wires to pass through your saddle. I think Erasmo was suggesting that you don't make a big cutout for a mag pickup, I tend to agree, but make it your own, there's no rules.

• ▶ Reply

Permalink Reply by Paul Craig on December 2, 2017 at 8:33am

Drill some pilot holes and use small screws instead of nails. That way you can remove the top if needed and nails might split the old wood.

• ▶ Reply

Permalink Reply by Kigar on December 2, 2017 at 9:30am

Just string pressure will hold it closed if the string retainer is not on the lid.

• ▶ Reply

Permalink Reply by Paul Cezanne on December 2, 2017 at 10:11am

awesome ideas, thanks so much.

This is a really welcoming community!

• ▶ Reply

Permalink Reply by Milt Haselmire on December 2, 2017 at 10:39am

Lots of good advice here so far.

I would add the rod piezo, and don't worry about thinning the top. If you have never used a router you are one slip away from destruction.

If you do everything else properly you will have the guitar you want.

That is a great looking box. 

• ▶ Reply

Permalink Reply by Taffy Evans on December 3, 2017 at 3:07pm

HI Paul, I like the box and think the thickness is ok. I think you will need a sound hole for the best effect.

You will get sound from the strings with no soundhole/s, but not much, if any, tonal quality. The air in the box which is excited by the tops vibration needs to get out of the box bringing with it [among other things] tone and volume.

I can see two areas on the right-hand side of the box where soundholes could be placed either side of the neck.

Cheers Taff

• ▶ Reply

Permalink Reply by Paul Cezanne on December 3, 2017 at 3:09pm

Thanks!

I'm going to try it first and then probably just cut the two holes. Besides, I like the looks of the holes!

• ▶ Reply

Permalink Reply by Taffy Evans on December 3, 2017 at 3:20pm

That's the way to go.

Taff

• ▶ Reply

• ‹ Previous
• 1
• 2
• 3
• Next ›
• Page