I have read several discussions and articles about resonant frequency, many of them going pretty deep into the science/engineering of piezoelectrics. Much of it was over my head as a beginner, and I've had a hard time finding a rough rule of thumb answer to a more fundamental question about resonant frequency.

So I have a very basic, bottom line type of question:

Q: In a very general sense, what is the optimal resonant frequency for a single disc piezo pickup to be mounted inside the box of a very simple cigar box guitar?

When shopping for Piezo discs, I have seen them of various size discs and ranging from a resonant frequency of 1.9±.5kHz to 9.2±1kHz, with most being between 4.0±.5kHz and 4.6±.5kHz. I don't know which resonant frequency rating is preferable for my purposes.

Please dumb the answers down for me. I know there are a million directions and a million level to which this type of conversation can go and that a thorough and precise answer probably has to begin with, "Well, it depends. . ." I know that's all important stuff, but I'm not there yet. I'll get there. Right now I'm really looking for beginner-level rough and general guidance for the fifth grader, so assume the following:

1. I'm using the simplest single disc to jack pickup with no preamp, pots, external power source or anything else.  Single piezo disc --> wires --> jack. (Again, I'll get there, but not this round)

2. I will mount it inside the cigar box, probably on the inside of the box top, just under the bridge, favoring the lower/bass string side.

3. I'm not looking for the highest quality sound or how to finesse it. I'm just wondering if there is any sort of general guidance for a quick build that sounds kind of cool when I plug it in in my living room to show a friend or two.

Final note: I have built one CBG with a simple single disc inside-the-box pickup and installed pickups in an acoustic guitar and in a ukulele. I also put a rod piezo in another acoustic guitar. I am very pleased with how they sound. However, I don't recall what the specs were on those first piezo discs I bought, and I may have just made a lucky guess when I bought them. If I'm going to buy a bunch more and start building more of these as a hobby (which I most certainly am, because I love it so far), I want to make a more educated guess when I buy the next batch.

In the following round of builds, I'll start thinking about preamps, pots, wiring a rod and disc in parallel, multiple disc locations, perhaps even active pickups and magnets, and all the other stuff I've been reading about.  

On a related but totally unrelated note, I also built an ES-335 style semi-hollowbody guitar from a kit, but that involved humbucker pickups. This is by far the coolest hobby I've ever stumbled upon, and since I build them with my 16 year old daughter (the family artist), it's doubly cool.

Thanks.

Bryan

Views: 1448

Reply to This

Replies to This Discussion

High impedance transducers like piezo devices have a very high impedance and will get loaded down by using volume controls in the 500K ohm to 1 Meg ohm range. This passive volume control is also in parallel with the input impedance of a typical guitar amp which is about 1 Meg ohms. If you combine these parallel loads it Looks like a 500 K ohm load to the piezo device.

Here is an experiment to try. Obtain a Scatten Design mini pre which has a 10 Meg ohm input impedance. Connect your piezo device directly to this preamp/buffer and plug your long guitar cable into the output of the mini pre and you will isolate the piezo device from the amp input loading and the effect of a 10 foot guitar cable having about 350 pico faraday (pf) of capacitance whose reactants (like resistance but at a specified AC frequency). The 350 pf cable capacitance looks like this ar various frequencies. 100 HZ 4,457,285 ohms, 1000 HZ 454,728 ohms, 5000 HZ 90,946 ohms and at 10000 HZ 45,473 ohms. So, as you can see higher frequencies are subject to more high frequency load but the Schatten mini pre isolates the piezo device from that loading because the output impedance of the mini pre is 3,500 ohms and even at the highest frequency the cable capacitance is over 10 Times higher than the output impedance and it looks like a bridging load on the preamp. Look up these words on the web “bridging impedance” and “matching impedance”. This will give you an appreciation for how cable types, lengths and source impedance values all interact to affect the sound you hear.

I hope this helps?

Joseph J. Rogowski

I've been wondering about using a high pass filter on one of these round piezo's myself. In a guitar situation, a .047 cap inline with the neck pickup's signal wire to the switch/volume pot can reduce the muddy tone of a neck pickup due to high bass. So I was thinking that a .022 or lower value cap would tame the high shrillness associated with the round piezo. 

The easiest way to control any piezo is to put a cap. acrossed the pickup leads. Simple no pots not perfect but cheap easy way to control it. try Gittys .068 caps. 

That's basically a tone cap passing highs to ground.

Haven't tried that without a volume pot. I'd rather have a volume pot so I can keep my amp settings at the sweet spot and also don't have to go back and forth to the amp that way. With a 500k volume pot, a .047 cap would probably work fine.

A preamp is cheap, and easy to install, and can really bring down the harshness of a piezo (and John Nickel would be happy, because you don't need giant blobs of hot glue). 

https://www.ebay.com/itm/3V-6V-TDA1308-Headphone-Amplifier-Board-AM...

https://www.ebay.com/itm/NE5532-OP-AMP-Audio-HIFI-Preamplifier-Dual...

A preamp is an excellent idea as long as it has a high input impedance - at least 1 Megohm and preferably higher.  Can't help noticing that neither of these ebay listings quote an input impedance.  Have they been tried in a CBG?  They might be OK but personally I'd go for a preamp specifically designed for buffering a piezo pickup. 

C.B.Gitty has 2 for 20bucks or less that work well with rod piezos. Don't know how well they work with disc piezos or the input impedance, but I'm sure they'll handle it just fine.

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

crossover guitar.

Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Mar 21. 11 Replies

Tune up songs

Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies

Duel output jacks

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies

How to Get Your Own Music on Spotify

Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray Feb 21. 2 Replies

CB Bass Guitar

Started by Mi Rankin in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Jan 27. 5 Replies

Latest Activity

BrianQ. commented on Dar Stellabotta's video
3 hours ago
BrianQ. liked Dar Stellabotta's video
3 hours ago
Southern Ray commented on Southern Ray's photo
Thumbnail

Project Punch!

" Thank ya again Keith!"
5 hours ago
Southern Ray commented on Southern Ray's photo
Thumbnail

Punch Project!

" Thank Ya Keith!"
5 hours ago
Doug Thorsvik commented on AGP #'s photo
Thumbnail

AGP #527 - ''Led-Zep 2''

"This build really strung you along Alan! Reminded me of all my fishing line experiments; a lot of…"
7 hours ago
Doug Thorsvik commented on A.D.EKER's video
Thumbnail

Im Troubled (Tribute) Mc K Morganfield by BCB - A.D .Eker 2024.

"Diggin’ the slow blues. I like that last pic Andries! Look at all those cool guitars. Yeah!!!"
7 hours ago
Dar Stellabotta posted a video

A Cigar Box Guitar Six Stringer Built by Louie Lamanna

This video is the unboxing and the demonstration of a beautiful, six stringer built by Louie Lamanna. Join Louie and I June 15 at the second annual Pittsburg...
8 hours ago
Doug Thorsvik commented on Doug Thorsvik's video
Thumbnail

Hail the Resurrection Day: 2-String Violin Chugger Cigar Box Guitar

"Happy Easter to you too Andries! The passion is definitely in full swing. Turns out I’m…"
9 hours ago
A.D.EKER commented on Doug Thorsvik's video
Thumbnail

Hail the Resurrection Day: 2-String Violin Chugger Cigar Box Guitar

"Happy Easter Doug ! the Passion is in full swing !"
9 hours ago
A.D.EKER commented on Ricky D's photo
10 hours ago
A.D.EKER commented on A.D.EKER's video
10 hours ago
Keith Rearick liked Doug Thorsvik's video
13 hours ago

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->