So, yea. I tried using actual frets for a fret board for the first time, needless to say I'm gonna have to scrap it. I can't get the frets to keep from rocking in the slots. Any tips? Anybody?

Views: 287

Reply to This

Replies to This Discussion

The problem is probably either a saw that is too wide or wood that is too soft. I have rescued the odd misscut fret by back filling with superglue and sanding dust and recutting.

I use a standard dovetail saw but have used hack saw blades. If the steel on your saw is thin enough you might narrow the kerf it cuts by hammering it slightly flat. I have a special tool called a saw set to spread the teeth sideways when I have to sharpen the saw and the kerf becomes too tight for the fret wire.

I used poplar, and I used the saw and fretwire from cb gitty. Would trying a harder wood be a good idea?

You can try gluing in the frets.   I always use a fretboard.   An oak fretboard would also add a lot of rigidity to your neck.  Over time the poplar will bow just a bit...

I really like a maple neck.. super hard, smooth... 

a spot of super glue will work.  leveling the frets makes or breaks a fretted instrument.  best thing i ever brought was a fret file. good luck and don't be put off, its fiddly, and adds hours to the build time but it is worth it.

Poplar is WAY too soft for fretboards - so soft that the slot won't really grip the tang of the fretwire and it is very easy to hammer or press the frets into the surface of the board and end up with uneven frets. It is also essential that your saw is cutting exactly the right width of slot - just a few thou of an inch too wide is enough to cause a problem. Here's how I install frets:

I have successfully fretted poplar.

Are you using a miter box or some other means to keep the saw stable and not letting it drift out of square?  If it drifts from square to the neck you get an hourglass slot that's wider at the edges.  If it drifts from square to the fingerboard the slot will be V shaped instead of U shaped and wider at the top where the tang barbs are supposed to grab the wood.  and finally are you making sure the slot is deep enough for the whole tang to go all the way down?

Yes, I have a miter box the make sure everything is in line. 

Thanks for the tips from everyone,  looks like I'll have to scrap it and start with a harder wood, probably oak.  I used a scrap piece of oak with the same setup to do a couple of test runs and in seemed to take care of the problem.  So here i go again, I guess.

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

crossover guitar.

Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Mar 21. 11 Replies

Tune up songs

Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies

Duel output jacks

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies

How to Get Your Own Music on Spotify

Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray Feb 21. 2 Replies

CB Bass Guitar

Started by Mi Rankin in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Jan 27. 5 Replies

Latest Activity

Dar Stellabotta posted a video

A Cigar Box Guitar Six Stringer Built by Louie Lamanna

This video is the unboxing and the demonstration of a beautiful, six stringer built by Louie Lamanna. Join Louie and I June 15 at the second annual Pittsburg...
41 minutes ago
Doug Thorsvik commented on Doug Thorsvik's video
Thumbnail

Hail the Resurrection Day: 2-String Violin Chugger Cigar Box Guitar

"Happy Easter to you too Andries! The passion is definitely in full swing. Turns out I’m…"
1 hour ago
A.D.EKER commented on Doug Thorsvik's video
Thumbnail

Hail the Resurrection Day: 2-String Violin Chugger Cigar Box Guitar

"Happy Easter Doug ! the Passion is in full swing !"
1 hour ago
A.D.EKER commented on Ricky D's photo
1 hour ago
A.D.EKER commented on A.D.EKER's video
1 hour ago
Keith Rearick liked Doug Thorsvik's video
5 hours ago
Keith Rearick liked A.D.EKER's video
5 hours ago
Keith Rearick liked Doug Thorsvik's video
5 hours ago
Keith Rearick liked Ricky D's photo
5 hours ago
Keith Rearick liked Ricky D's photo
5 hours ago
Keith Rearick liked Ricky D's photo
5 hours ago
Keith Rearick liked Ricky D's photo
5 hours ago

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->