After building a dozen CB Ukes, I came across a beautiful 48" long piece of Redheart lumber that I couldn't bear to cut down for a uke. So I found a bigger cigar box on vacation in NOLA (a "Cuban Spliff"; only a crazy CBGer brings home an empty cigar box from Mardi Gras...), and now I'm making a standing bass. I'm puzzling about the scale length, but 35" seems about right --- like a short scale bass guitar --- if I want the neck to go through the box and out what will be the bottom. I've already installed a 6-inch resonator. I plan to use a flying trapeze for a mandolin as the tailpiece. I'm going to make a puck and install a piezo rod pick-up under the saddle. I'm using horn for the saddle; I couldn't find a big enough piece of bone. I'm going to taper the yellowheart fingerboard from about 1-1/2 at the nut to about 2 inches at the bottom, and I'm going to leave it fretless. But I think I'll install markers on the side of the fingerboard at the first octave (first G harmonic), at D above the first octave and at the second octave (higher G harmonic). Apparently installing markers on the fingerboard is crass to bass players. I planned to load it with strings for a standing bass (GDAE from high to low), but --- expletive deleted --- they're expensive. I'd like to use something classier than weed whacker line.

OK. So. Does anyone have any experience building these things who might like to comment and offer suggestions and tips. Is a 35" scale enough? Will a mando tailpiece work? Does that mean I need strings with a little loop or the end, or will ball ends work? What relatively economical strings should I get? Any thoughts? Thanks CBGers!

Larry

Views: 227

Attachments:

Replies to This Discussion

Most traditional basses (guitar style) are 34-35" scale, so that should work just fine... I might worry about the string pull without a truss rod.

You'll need a raised fretboard otherwise the tailpiece might leave the action too high...   Other than that, it sounds like a phenomenal idea!  

I've made 2-string bass out of 1x2 maple with a Brazilian cherry (Jatoba) fretboard...

Thank you!

I've been using inexpensive Orphee strings on my 3 stringers (their regular RX Slinky equivalents) and am happy with the results.  You could give these a try, they are from their High End line.

http://www.ebay.com/itm/Orphee-DEB-9X-Electric-Bass-Strings-045-100...

Thank you!

I made a nice weed wacker line ("nylon stringed") bass guitar a while back that came out great. I had to source the different thickness line from eBay, but the customer and I thought it sounded great.I want to build another, as well as a Suitcase Standup Bass. Maybe I'll get the guts when I have a clear cut plan... 

Thanks, Brian. I'm going to try a couple of string choices to see which I like most.

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Discussion Forum

Cutting deep boxes in half

Started by Justin Stanchfield. Last reply by Taffy Evans Mar 20. 9 Replies

Attention 1st time builders!

Started by BrianQ.. Last reply by MadGomer Feb 27. 2 Replies

Brickhouse CBG Wiring

Started by Ian Boyd. Last reply by Ian Boyd Dec 11, 2023. 1 Reply

Fretless fret markers

Started by Michael Myers. Last reply by Michael Myers Apr 20, 2023. 8 Replies

canjo building and tuning

Started by Brenda. Last reply by MadGomer Dec 3, 2022. 5 Replies

Minimum tools needed

Started by Wichita Sam. Last reply by Taffy Evans Nov 14, 2022. 21 Replies

High G problem

Started by Michael Myers. Last reply by Taffy Evans Nov 3, 2022. 4 Replies

Doubling the high string

Started by Robert Killen. Last reply by Paul Craig Oct 14, 2022. 23 Replies

Aluminum License Plate

Started by Larry Sobol. Last reply by Larry Sobol Oct 1, 2022. 6 Replies

C. B. Gifty three string fretless kits.

Started by jon neet. Last reply by Taffy Evans Aug 16, 2022. 6 Replies

Frettin' and stainin'

Started by Doug Laffin. Last reply by Order99 Aug 11, 2022. 4 Replies

Bolt on neck to a set neck body?

Started by Paul Craig. Last reply by Paul Craig Jul 17, 2022. 14 Replies

Locations

Started by Roy Smith. Last reply by the anonymous pick May 15, 2022. 2 Replies

Help please re Bento Box Uke "nut"

Started by Al Lobe. Last reply by BrianQ. May 10, 2022. 18 Replies

Clarification on pick ups

Started by Michael Myers. Last reply by Taffy Evans May 6, 2022. 5 Replies

Licence plate cbg

Started by Michael Myers. Last reply by Michael Myers May 2, 2022. 5 Replies

Builder's Tips

Started by Wichita Sam. Last reply by MadGomer Feb 23, 2022. 2 Replies

Getting there but needing advice/help please.

Started by Lionhound. Last reply by MadGomer Feb 18, 2022. 8 Replies

Tres Cubano Build

Started by Paul Craig. Last reply by Paul Craig Dec 9, 2021. 18 Replies

CB Gitty Country Roads Banjo kit

Started by Ken Hope. Last reply by Christopher G Daniels Nov 29, 2021. 4 Replies

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->