Hi guys.

I'm on my third build and decided to use a walnut neck saddled over the box, but man it is so light! I ain't no carpenter so a little advice on good woods for the neck would be appreciated, is walnut ok or should I go for more dense heavier woods like oak or mahogany???

Views: 501

Reply to This

Replies to This Discussion

Walnut is fine, a lot of folks use poplar, too. My preference is maple, as it is very hard, and easy to sand to a glass smooth finish.

If you are dadoing the neck, you might want to reinforce the neck with a piece that runs the length of a box and prodtrudes an inch or two as a heel to prevent bowing.

Hi John

Thanks for the advice. Maple is soooooooo expensive here in the UK, but I guess you get what you pay for

Oak, on the other hand, should be readily available in the UK. What do they make pallets out of there? You can often find hardwood pallets going begging...
Hi Neil,Walnut will make a great neck, it can have a beautiful look when finished well, another good wood to use over this side of the pond is European Beech, very nice looking and good to work with.
I don't know how many pallets are hardwood, never been able to find one, but perhaps that's just me.
One other general tip is to use Quarter sawn timber where you can afford to, it is much more musical sounding and strong; it rarely warps in normal conditions.
All the best from Bill. :D

careful picking through the wider boards that were plain/flat-sawn (cheaper), and you can get close-enough perpendicular grain/rings for a neck from the edges of a bigger board, and then use the remainder for blocking or other non-git-neck stuff.

Hi Bill, thanks for the advice but, seeing as I'm a total ignoramus when it comes to timber, could you please explain what ''quarter sawn'' is.

Many thanks

found this from google image search

Walnut is not a particularly light timber...are you sure it really is walnut? It's only about 10% less dense than sapele and  maple, certainly not as light as stuff such as  poplar.

Hi John, I did buy it off ebay so I guess you can never be 100% sure. My first build has  a European white oak neck and my second has a mahogany neck, both do seem  heavier but maybe I'm exaggerating a little.......out with the scales!!

Hi Neil, Quarter Sawn timber is a more expensive cut of wood. If you look online at Wikipedia or do a google search you will get a better idea when you have a diagram to show how a log is sawn lengthways into quarters and sliced into boards. You will see how more waste wood is created this way, hence the higher cost. (Check it out, you will be able to understand better with the diagrams and a better worded explanation. This wood has superior qualities for construction (it retains more of the strength of the fibres of the wood, therefore it is less prone to splitting and warping and is easier to work with).
Hope this helps.

Hi Neil,
I've done a couple walnut necks that worked okay, though I usually prefer to use maple for the neck with a walnut fretboard glued on, which is stronger and more stable. It's not unusual for it to feel lighter than white oak.

Here's a better view (with worse focus...) of the drawer pull tailpiece you asked about, this was the only place I could seem to post it for you. You can see that the top of it sits just above the box top, allowing room for the strings to pass through holes drilled for them. This gives as much "break angle" as possible over the nut, with limited torque on the end of the box (which is attached to the end of the neck anyway, which keeps it from being torqued by the string tension).

Attachments:

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

crossover guitar.

Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Mar 21. 11 Replies

Tune up songs

Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies

Duel output jacks

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies

How to Get Your Own Music on Spotify

Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray Feb 21. 2 Replies

CB Bass Guitar

Started by Mi Rankin in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Jan 27. 5 Replies

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->