Hello all of you knowledgeable instrument builders,

After building three four string guitars, a three string guitar, an eight string mandolin, an ukulele, and a diddley bow I feel ready to graduate to building a six string.

The only problem is that I'll need a truss rod for that and I do not have any power tools (except for a drill). So how do I cut a straight and even truss rod groove without a router?

Any suggestions?

My only idea so far is to make a three part laminate neck with the middle part the same width as the square metal rod I want to use as a nonadjustable truss rod. Something like the sketch below.

Do you think that would work? Has anybody done this successfully?

Thanks!

Views: 5923

Reply to This

Replies to This Discussion

I've built 15 guitars. I don't use truss rods. I bury a length of 1/2" square tube in the neck. None of them have moved yet.

If there is a high school in your area that has a wood shop, ask the teacher if someone could rout out your neck for a truss rod.  You could offer to give a talk on what you are doing.  There might even be students who would be interested in building cigar box guitars.  I think most shop teachers would be interested in community involvement.  

You can get double-action adjustable truss rods quite cheaply on Ebay.

Although I routed out the slot on my 6-string, from the rear, I don't see any reason why you couldn't laminate a neck around the truss rod.

Access to the adjustment screw is via an Allen key through a hole in the front of the headstock.

Tim

It'll work with two pieces (2) as well, can be done with a dovetail saw, regular or Japanese... For a smaller builds a cross-grain laminate (1) is more than enough...

You sir are correct, cross grain laminate is strong enough to leave out the metal bar,., but I guess this thread is about installing a bar...

Well, you could always redneck it and chuck your drill in a vice, zip-tie the trigger and run it by hand under the bit. may not be perfect, but aint that kinda the point of a CBG?

Hi, Just done this job today and it fits in with this thread, so I thought I would post my process.

The finger board was off due to the neck bowing up, so after straightening the neck I hand cut the slot sides with hand saws and chiselled out the waste  to fit the reinforcement infill. I made a depth gauge out of brass to fit the 1/16 chisel so I could scrape the bottom of the slot flat and level.

Easy peazy. Taff

I suppose you could use a chisel, then fill the trough with epoxy for a tight fit?

Inspired by this thread I've just completed a neck for a 'normal' 6-string guitar, using an adjustable truss rod within a laminated neck.

The guitar had yet to be completed, but it looks OK so far!

Tim

I taped little bits of card to the top of the rod to increases its apparent depth. This allowed me to true up the top of the neck with a little bit of leeway.

An access hole for the 4mm Allen key for adjustment.

#

Hi Tim, that all looks good, but an observation if I may. I feel it would be more beneficial to use a wood infill on top of the rod. Over time the cardboard is liable to compress and leave you with a loose rod. Also the rod is then pushing against the fingerboard and not, maybe, the air gaps.

Just a thought Taff

My fault Taffy,

I did remove the bits of card prior to gluing it all together.

Any rattles can be eliminated by adding a little bit of tension to the rod.

Tim

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

crossover guitar.

Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Taffy Evans yesterday. 8 Replies

Tune up songs

Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies

Duel output jacks

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies

How to Get Your Own Music on Spotify

Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray Feb 21. 2 Replies

CB Bass Guitar

Started by Mi Rankin in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Jan 27. 5 Replies

Latest Activity

BrianQ. liked Gary O'slide's video
2 hours ago
Doug Thorsvik commented on Doug Thorsvik's photo
Thumbnail

Flathead Diddley Bow

"Thanks. Wow! That becomes a spendy box Alan. They are pretty distinctive though. I have a few on…"
6 hours ago
Nigel McTrustry posted a video

Nigel McTrustry & The Hound Dogs are Loose! - Yellow Dog - Live - Original - Cigar Box Guitar

Nigel McTrustry & The Hound Dogs are Loose! Yellow Dog (McTrustry)@ The Cave Inn Brisbane, Australia.The song is currently on Spotify.
6 hours ago
AGP # commented on Doug Thorsvik's photo
Thumbnail

Flathead Diddley Bow

""Sweet Doug" :-), have seen quite a few Flathead Builds over the years, great looking…"
9 hours ago
AGP # liked David Dodt's photo
9 hours ago
AGP # liked David Dodt's photo
9 hours ago
AGP # liked David Dodt's photo
9 hours ago
AGP # liked Doug Thorsvik's photo
9 hours ago
AGP # liked Doug Thorsvik's photo
9 hours ago
AGP # liked Doug Thorsvik's photo
9 hours ago
AGP # liked Aaron Green's photo
9 hours ago
Keith Rearick liked Gary O'slide's video
10 hours ago

Events

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->