I just did my first build using a lightning reso cone from Gitty and at the end found I had a problem with intonation. I laid everything out first as I always do, used a 24" scale. I was very careful to measure twice and cut once for the hole to hold the cone. All done and string it up and something is not right, intonation is off. I used a medium action since I wanted to do both slide and finger notes, it is fully fretted. I know it will go a bit sharp if the action is too high. So , to get the intonation to be correct , I had to slide the discuit/ saddle back by a bit over 1/4", so now the biscuit is not centered on the cone "nipple" like it should be but teetering on the edge. I think I will make a new biscuit/saddle on an oval shape (maybe rectangle) and screw it to the cone so it does not tip off the edge of the "nipple". I've done resonators before but never one where moving the biscuit causes a problem. I guess the moral of the story is I needed to figure in some "compensation" in my calculation of where to mount the cone on the box for my scale length.

Anyone else run into this??

Views: 894

Reply to This

Replies to This Discussion

Fretting a string can only sharpen a note, never flatten it, as you are deflecting the string from a straight path thus increasing the tension in the string..that's why when setting a bridge it will always be further away from the nut than the theoretical scale length.

One can get a flat note, and I find it when I am setting customers guitars up. If you press on the string pushing it to the fingerboard, behind the fret,and set the intonation to that note, you can get a lower note if the string is pushed more softly and maybe stops at the fret, so not being stretched as far.

This is often experienced when setting intonation for other players, they all have different playing styles so setting spot on intonation can be tricky.

I have tested this by fretting a string whilst watching the tuner and rolling my finger behind the fret,I can make the note go flat and sharp, if I set it with a firm pressure on the string to start with.

So l have developed a method to over come this.
Cheers Taff

Depending on the design of your git,could you relocate the fingerboard/nut away from the saddle using a bit of creative bodging?

That is actually a really good idea and one I had not thought of. I could add 1/4" to the length of the through neck . I'm not sure if I would like it visually as I have the fretboard meeting up with the body right where I want it now but thanks for the food for thought! I think this is similar idea that another poster suggested, but they were talking, pre build. I had not thought of it as a retrofit.

you can trim out the neck to box where they meet

Make another fingerboard,you can always use this one on a future build.

Fingerboard is glued on and fretted, fret spacing etc are fine. I'm going to go with the simplest solution, make a new biscuit with the slot cut off center. 

Thank you all again for all the helpful suggestions!!

Before you move the resonator back check the break angle of the strings and adjust if necessary. I ran into this problem and moved the res back. Still had an issue. I ended using the neck on a different git and had the same problem. I finally discovered the break angle was all wrong eventually after slowing down and taking a closer look. Even if it isn't wrong, the angle of the strings can influence better intonation. 

Hi, changing the break angle at the bridge and/or nut would have an effect on how the strings feel, soft or tight, and may tie in with what I mentioned on this thread earlier. The fact that finger pressure on strings when setting intonation can effect good intonation. Soft strings and soft/light tension may allow the string move more under finger pressure. Giving a false note against the harmonic.

Taff

Note to self measure 3 times. most my build have floating bridges but not all now i'll think twice thanks Bluesheart.

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

crossover guitar.

Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Taffy Evans yesterday. 8 Replies

Tune up songs

Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies

Duel output jacks

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies

How to Get Your Own Music on Spotify

Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray Feb 21. 2 Replies

CB Bass Guitar

Started by Mi Rankin in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Jan 27. 5 Replies

Latest Activity

BrianQ. liked Gary O'slide's video
2 hours ago
Doug Thorsvik commented on Doug Thorsvik's photo
Thumbnail

Flathead Diddley Bow

"Thanks. Wow! That becomes a spendy box Alan. They are pretty distinctive though. I have a few on…"
7 hours ago
Nigel McTrustry posted a video

Nigel McTrustry & The Hound Dogs are Loose! - Yellow Dog - Live - Original - Cigar Box Guitar

Nigel McTrustry & The Hound Dogs are Loose! Yellow Dog (McTrustry)@ The Cave Inn Brisbane, Australia.The song is currently on Spotify.
7 hours ago
AGP # commented on Doug Thorsvik's photo
Thumbnail

Flathead Diddley Bow

""Sweet Doug" :-), have seen quite a few Flathead Builds over the years, great looking…"
9 hours ago
AGP # liked David Dodt's photo
9 hours ago
AGP # liked David Dodt's photo
9 hours ago
AGP # liked David Dodt's photo
9 hours ago
AGP # liked Doug Thorsvik's photo
9 hours ago
AGP # liked Doug Thorsvik's photo
9 hours ago
AGP # liked Doug Thorsvik's photo
9 hours ago
AGP # liked Aaron Green's photo
9 hours ago
Keith Rearick liked Gary O'slide's video
10 hours ago

Events

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->