My very first fret. Coping saw, side snips, no fret wire radiusing, and a tiny flat file. It's loose but it's in there. You can see where the file slipped off the feet and hit the wood a little. Really itchin to purchase some tools to make this fretting business go faster!

Views: 245

Attachments:

Reply to This

Replies to This Discussion

You need to super glue those loose frets, Richard. Glue and clamp immediatley. Use regular crazy/super glue, it penetrates into cracks. You need to look very closely at each fret, and press with you thumbnail. If you see even the slightest movement, glue it or it will buzz. 

nice work, I don't have the patience to do onsies.

I just whack the first bit of a wire in, use a dremmel to trim it and go on to the next

then use a belt sander to dress the frets and side of the fingerboard and neck in one whoop.

Well, Richard, there are many articles within this forum regarding fretting methods, tools, and results. Wayfinder recently posted an article on low cost fretting tools and such which you might find useful.

I have tried several methods, with good results (my opinion). Currently, I have been using the "install and trim/finish" method, which is the method I always come back to after trying alternative methods. JL's post describes the same basic method.

Tools: after trying every saw I could put my hands on, I bought a ZONA saw from CB Gitty (also available at Amazon). This saw cuts my medium/medium fret slots perfectly. I then install a piece of fret wire @ 2" wide into the slot using a bar clamp (see Wayfinder's post) and use a small block of red oak and a rubber mallet to for-sure seat the fret. Then side cutter/nipper to trim the fret as close to the fret board. Next, I use my 1/3 sheet sander to finish the fret ends flat with the edge of the fret board. I also bought a fret edge file (from CB Gitty) to finish/bevel the fret ends. A little bit of fine smoothing with a needle file. Lastly, a bit of fine grit sandpaper to polish out the beveled end. Fret saw -@ $15.00, Fret end file @$45.00 or so. Clamps, sander, hand files, etc. I already had.

I use this method on fretboards both prior to or after gluing the fret board to the neck. Depends on how I feel about each build. Sometimes I have to hit the edge of the fretboard with a little more stain, but usually I like the "weathered" look a little sanding gives the edge of the fret board. I put the poly finish(I use MinWax rattle can) on at the very end.

This is a lot of words, and in my head I can see it all step-by-step. It is much easier now than at first. I've fretted @ 25 fret boards and the tools I use now are a combination of what works best for me within a reasonable budget. The popular cut-and-finish the fret before installation is a good method. I have used it for several builds, but I keep going back to what works best for me and my tools. Try what you think will suit your skill and tools, and experience(s) will reveal what is best for you. Most will probably agree that early attempts will whet your appetite for improvement, and subsequent builds will show you how to get there. Again, many posts within the Nation to assist you in learning.Good luck.

Great start.  I use a fret saw so they slid in there nice and tight.  You can't push them down by hand, I made a little tool to attache to my drill press to press them down into the fret board, drill press turned off of course. I also use a dermal tool to file off my end and if I hit the wood a little, I sand the whole neck down so it all matches and you never know the difference.

RSS

The Essential Pages

New to Cigar Box Nation? How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building Basics

Site Sponsor

Recommended Links & Resources


Forum

crossover guitar.

Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Mar 21. 11 Replies

Tune up songs

Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies

Duel output jacks

Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies

How to Get Your Own Music on Spotify

Started by Cigar Box Nation in Feature Articles. Last reply by Southern Ray Feb 21. 2 Replies

CB Bass Guitar

Started by Mi Rankin in Building Secrets, Tips, Advice, Discussion. Last reply by Justin Stanchfield Jan 27. 5 Replies

Latest Activity

Doug Thorsvik commented on AGP #'s photo
Thumbnail

AGP #527 - ''Led-Zep 2''

"This build really strung you along Alan! Reminded me of all my fishing line experiments; a lot of…"
1 hour ago
Doug Thorsvik commented on A.D.EKER's video
Thumbnail

Im Troubled (Tribute) Mc K Morganfield by BCB - A.D .Eker 2024.

"Diggin’ the slow blues. I like that last pic Andries! Look at all those cool guitars. Yeah!!!"
1 hour ago
Dar Stellabotta posted a video

A Cigar Box Guitar Six Stringer Built by Louie Lamanna

This video is the unboxing and the demonstration of a beautiful, six stringer built by Louie Lamanna. Join Louie and I June 15 at the second annual Pittsburg...
2 hours ago
Doug Thorsvik commented on Doug Thorsvik's video
Thumbnail

Hail the Resurrection Day: 2-String Violin Chugger Cigar Box Guitar

"Happy Easter to you too Andries! The passion is definitely in full swing. Turns out I’m…"
3 hours ago
A.D.EKER commented on Doug Thorsvik's video
Thumbnail

Hail the Resurrection Day: 2-String Violin Chugger Cigar Box Guitar

"Happy Easter Doug ! the Passion is in full swing !"
3 hours ago
A.D.EKER commented on Ricky D's photo
3 hours ago
A.D.EKER commented on A.D.EKER's video
3 hours ago
Keith Rearick liked Doug Thorsvik's video
7 hours ago
Keith Rearick liked A.D.EKER's video
7 hours ago
Keith Rearick liked Doug Thorsvik's video
7 hours ago
Keith Rearick liked Ricky D's photo
7 hours ago
Keith Rearick liked Ricky D's photo
7 hours ago

Music

© 2024   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service

\uastyle>\ud/** Scrollup **/\ud.scrollup {\ud background: url("https://storage.ning.com/topology/rest/1.0/file/get/963882636?profile=original") no-repeat scroll 0 0 transparent;\ud bottom: 25px;\ud display: inline !important;\ud height: 40px;\ud opacity: 0.3 !important;\ud position: fixed;\ud right: 30px;\ud text-indent: -9999px;\ud width: 40px;\ud z-index: 999;\ud}\ud.scrollup:hover {\ud opacity:0.99!important;\ud}\ud \uascript type="text/javascript">\ud x$(document).ready(function(){\ud x$(window).scroll(function(){\ud if (x$(this).scrollTop() > 100) {\ud x$('.scrollup').fadeIn();\ud } else {\ud x$('.scrollup').fadeOut();\ud }\ud });\ud x$('.scrollup').click(function(){\ud x$("html, body").animate({ scrollTop: 0 }, 600);\ud return false;\ud });\ud });\ud \ua!-- End Scroll Up -->