So this is the design I am thinking of for my new rig. I am still working out the bugs, this was the first time I even tried it out on the bench. So bare with me.

I was thinking flap pup design, and I always thought it would be cool to make a pup that you could hide all of the coil in the box and just have the magnets on the top.

So was at home depot and picked up some metal strapping for air duckting, and wrapped some wire around it, hooked up a jack and some magnets and I get a real faint signal.  Part of the reason I think is my coil is pretty weak. I just hand wrapped it a few times just to try it out.  

The reason I was wanting to do this was, I could cut a small slit of the lid of my cigar box, run the bottom piece of the metal strapping inside the box, with coil wrapped around the strapping inside, or I think I may just wind some small sewing bobbin coils and attach them to the strapping, fold the strapping down on the box lid on the outside, add the magnets and hot glue or fasten the strapping to the top of the lid with screws

The strapping is under 2 bucks for a pretty good size roll, you could make several pickups out of just one roll.
,

this strapping is kinda weird, because it has holes and then a set of slots, but I think we can come up with something. The the coil wires can be hooked up in the box, and too the jack, no fuss no muss.

I was thinking sewing bobbins, or maybe just a fat bolt wound with wire, or a large coil wrapped with wire, or something of a kind of coil in the box, any size you want.  Attach the strapping to the coil and add magnets. I think I might pick up some sewing bobbins and some bolts tomorrow at wally world. Let me know what you guys think, or maybe calibrate on the design, or let me know if someone has all ready tried this.  Thanks for looking.  Hope this sparks some new ideas.

Views: 106

Reply to This

Replies to This Discussion

keep in mind, the way this is set up right now is kinda upside down the, strapping would be bent the other way, I just had it like this because it was easier this way to test it with my diddley bow.

That will work Jerry, but not all that well, output will most likely be weak, getting your magnets closer to the coil will help, the flat pup concept of a 4-500 wind coil either side of the magnets, wound in opposite directions is hard to beat if you are going to go to the bother of winding a pup of that nature, for a simpler diy job, have a look at the induction type pick up, the thread is being rejuvinated at the moment, but it has all the basics there. Almost any mag pup van be mounted out of sight if you wish, some can be powerfill enough to work through the soundboard with nothing added, while others may need poles or a bar coming through the soundboard

"There Are NO rules" means try something and share the results and we all learn.

and that looks like an interesting variation of the principals that a flat pickup works on. As Darryl said, the farther the coils is from the magnets, the weaker the signal is likely to be.  the field needs to go out around and back in through the core and coil.  magnetic fields get weaker by the cube of the distance they have to travel.

that principle also relates to the distance of the string above the magnetic field. so if you mount the pickup 1/2"from the strings say under the sound board then the signal out will be 1/4 the strength of a signal if the pickup was mounted 1/4" under the strings... 

you could still mount the magnets on top of the sound board and the coil directly under them in the inside of the box. the coil would need a small piece of the strapping as a core. if the magnets are strong then the output should be strong enough...the wood of the box wont have any effect on the magnetic field..

The magnets are attached to the strap that the wire is wrapped around, so the strap will act like a pole for the coil. It will work. Strength of output will depend on magnet strength and amount of coil winding. Will the disruption of magnetic field make it to the coil? Let's see.

Things to do differently with this design:

1) Wrap the wire completely around the magnets, not the strap.
2) The strapping is what? Steel, or aluminum?
3) Encase the magnet-wrapped wire in the presumably-steel strapping, then wire to a jack.
4) Wrap the presumably-steel strapping around the magnets. Then do your wire wraps around that. The way you have it now in the photo is the reason for the very weak signal you got.
4) Use a SINNGLE LOOP of 6 AWG wire around the round edges of the magnets, and wrap that with black electricians tape. Feed one leg of the 6 AWG wire through the center hole of a AS-104 mini-transformer, or alternatively, crack open a used wall wart, and use one of the two trannies inside for the same purpose. Wire to a jack. You have then created a version of the induction pup design, currently shown on the in-progress-of-reconstitution of the Induction Pup thread.

RSS

The Essential Pages

New to Cigar Box Nation?How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources

Forum

Cigar Box Limberjack Toys by Wade Costenbader

Started by Shane Speal shanespeal.com in Feature Articles. Last reply by Dave Lynas 5 hours ago. 17 Replies

Slapback rockabilly pedal

Started by Blind Boy Fullers in Performances, How to Play, Lessons, Concerts. Last reply by Cause the Blue rat 8 hours ago. 12 Replies

2017 Plumber's Challenge Winners

Started by Shane Speal shanespeal.com in Feature Articles. Last reply by Kevin Perlic yesterday. 11 Replies

Screw Sizes

Started by Phil Gershwiin in Performances, How to Play, Lessons, Concerts. Last reply by Grandpa yesterday. 5 Replies

1935 Limberjack Plans - Free Download

Started by Shane Speal shanespeal.com in Feature Articles. Last reply by Michael Carey on Monday. 1 Reply

Latest Activity

Erasmo Coco commented on AGP #'s photo
Thumbnail

Too Many Guitars ?????????

"AGP is that you wearing that shirt ? ( perfect fit ! )  (-:"
26 minutes ago
Andries D. EKER commented on shane wagstaff's video
Thumbnail

Rock Hill Radio 3

"Thanks Shane ! its hard for me to tune in on line, but these excerpts from the radio show do there…"
50 minutes ago
Andries D. EKER commented on Cpt. Nemoff's video
Thumbnail

Heavy Lime - Red Machine

"great little groep Capt; soulfull editing!"
54 minutes ago
Andries D. EKER commented on Andries D. EKER's video
Thumbnail

When it hits Ye ! A D Eker 2017

"deeper in to the Blues listen to the Beat of the Soul the Bitch and Moan Club takes you down !"
56 minutes ago
Andries D. EKER posted a video

When it hits Ye ! A D Eker 2017

Deeper in to the Blues , crying and Moaning, The Bone is pick'ed, just a man his mind and his Guitar, get ready for some heart tearing Blues! below the belt ...
1 hour ago
Andries D. EKER commented on Wade's video
Thumbnail

Johnny & The Devil Limberjack Duel!!!

"Genus on the dubble mover Wade love a closer look on that contraption!!"
1 hour ago
Andries D. EKER commented on Richard Sundberg's video
Thumbnail

My Wife Wants To Plant Flowers On My Head

"Dont let her ,it will just take away from your CBG Playing time, or get a splitter and buy one…"
1 hour ago
Richard Sundberg commented on Richard Sundberg's video
Thumbnail

My Wife Wants To Plant Flowers On My Head

"Thanks Uncle! Yeah, I have a Linda too! She liked the humor and satire and metaphors, but also said…"
1 hour ago
JL replied to Mark McCann's discussion CB Gitty Amp Build assistance needed...
"A hot battery means a short. Use a multi-meter and check the battery connector for a short between…"
1 hour ago
Jerry Jordan replied to Mark McCann's discussion CB Gitty Amp Build assistance needed...
"Darryl is right,.a hot battery indicates a direct short across the battery.., You need to probe the…"
1 hour ago
JL replied to Hal Robertson's discussion Festival Display
"carry a few scrap squares of plywood to put under each corner of the display stand to prevent…"
2 hours ago
Eric Lettau posted photos
2 hours ago

Music

Loading…

© 2017   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service