So, yea. I tried using actual frets for a fret board for the first time, needless to say I'm gonna have to scrap it. I can't get the frets to keep from rocking in the slots. Any tips? Anybody?

Views: 118

Reply to This

Replies to This Discussion

The problem is probably either a saw that is too wide or wood that is too soft. I have rescued the odd misscut fret by back filling with superglue and sanding dust and recutting.

I use a standard dovetail saw but have used hack saw blades. If the steel on your saw is thin enough you might narrow the kerf it cuts by hammering it slightly flat. I have a special tool called a saw set to spread the teeth sideways when I have to sharpen the saw and the kerf becomes too tight for the fret wire.

I used poplar, and I used the saw and fretwire from cb gitty. Would trying a harder wood be a good idea?

You can try gluing in the frets.   I always use a fretboard.   An oak fretboard would also add a lot of rigidity to your neck.  Over time the poplar will bow just a bit...

I really like a maple neck.. super hard, smooth... 

a spot of super glue will work.  leveling the frets makes or breaks a fretted instrument.  best thing i ever brought was a fret file. good luck and don't be put off, its fiddly, and adds hours to the build time but it is worth it.

Poplar is WAY too soft for fretboards - so soft that the slot won't really grip the tang of the fretwire and it is very easy to hammer or press the frets into the surface of the board and end up with uneven frets. It is also essential that your saw is cutting exactly the right width of slot - just a few thou of an inch too wide is enough to cause a problem. Here's how I install frets:

I have successfully fretted poplar.

Are you using a miter box or some other means to keep the saw stable and not letting it drift out of square?  If it drifts from square to the neck you get an hourglass slot that's wider at the edges.  If it drifts from square to the fingerboard the slot will be V shaped instead of U shaped and wider at the top where the tang barbs are supposed to grab the wood.  and finally are you making sure the slot is deep enough for the whole tang to go all the way down?

Yes, I have a miter box the make sure everything is in line. 

Thanks for the tips from everyone,  looks like I'll have to scrap it and start with a harder wood, probably oak.  I used a scrap piece of oak with the same setup to do a couple of test runs and in seemed to take care of the problem.  So here i go again, I guess.

RSS

The Essential Pages

New to Cigar Box Nation?How to Play Cigar Box GuitarsFree Plans & How to Build Cigar Box GuitarsCigar Box Guitar Building BasicsCigar Box Guitar Parts Store

Site Sponsor

Recommended Links & Resources

Forum

2017 Halloween Build-Off!

Started by Shane Speal shanespeal.com in Feature Articles. Last reply by Jed Schaffer 7 hours ago. 56 Replies

Hubcap grounding issues

Started by Colin Trundle in Building Secrets, Tips, Advice, Discussion. Last reply by darryl kernaghan 13 hours ago. 11 Replies

seeking advice

Started by Michael Graves in Performances, How to Play, Lessons, Concerts. Last reply by Titch the Clown 23 hours ago. 4 Replies

Intruduction

Started by Martin Ford in Other stuff - off topic, fun stuff, whatever. Last reply by Martin Ford yesterday. 2 Replies

Banjo question

Started by Rose Ericson in Performances, How to Play, Lessons, Concerts. Last reply by Titch the Clown on Tuesday. 46 Replies

Latest Activity

Mike posted photos
7 minutes ago
Tom E commented on Tom E's photo
Thumbnail

Game of thrones

"Trying to put the song into tab for 4 stringer"
9 minutes ago
Tom E posted a photo
14 minutes ago
Jeff 'Bones' Reilly commented on Jeff 'Bones' Reilly's photo
Thumbnail

#14

"=[]"
43 minutes ago
the anonymous pick replied to smilingdog1's discussion St. Louis MO. CBG Club/Workshop
"sweet .  glad you all had a good time  , some great entries here pat yourselves on the…"
1 hour ago
the anonymous pick commented on Erasmo Coco's video
1 hour ago
Dave Lynas commented on Andries D. EKER's video
Thumbnail

Leaf's Lament A D Eker 2017

"The very best yet Andries. Beautiful languid play! Thanks very much."
1 hour ago
Dave Lynas liked Andries D. EKER's video
1 hour ago
Dave Lynas commented on Erasmo Coco's video
Thumbnail

Poor Man's Resonator Blues ( Cookie Tin Guitar)

"Love the tin tone slider. Our beautiful dry week is chilling. Winter lurks. I like the unaltered…"
1 hour ago
the anonymous pick commented on Jeff 'Bones' Reilly's photo
Thumbnail

#14

"i need more info  :-}"
1 hour ago
the anonymous pick commented on Kentucky Mojo's photo
Thumbnail

Skully

"slick."
1 hour ago
the anonymous pick commented on Jed Schaffer's photo
Thumbnail

dsm

"vey cool . good luck in the contest ;-)"
1 hour ago

Music

Loading…

© 2017   Created by Ben "C. B. Gitty" Baker.   Powered by

Badges  |  Report an Issue  |  Terms of Service