#1 resource for Cigar Box Guitars, Free Plans, How-To, Parts & More!
Cigar Box Nation is sponsored by C. B. Gitty Crafter Supply, your one-stop-shop for Cigar Box Guitar parts and accessories!
Easy Scarf Joint on Miter saw.
Hi all, I just recently joined the Cigar Box Nation! I happened upon this site while building my first cigar box guitar. I have learned a lot from all of you in regards to building these awesome guitars. Although, I had some trouble figuring out how to make a scarf joint without a table saw, so I came up with this idea. I noticed there is a lot of discussion about how to make the joint and I wanted to share this easy trick with all of you.
1. take a 3/4" pine board about 12" long and cut one end at 15 degrees with miter saw.
2. attach a strip of wood to the back side of cut piece of wood to clamp to the saw.
3. attach another small strip along the angle you just cut to help "rest" your neck material against.
4. cut a headstock peice about 6 inches or so.
5. set saw to 0 degrees with jig attached to miter saw.
6. cut the 15 degree angle on the headstock piece using the jig.
7. cut the 15 degree angle on the neck and glue and clamp the two together.
See attached photos!
- Attachments:
-
-
IMG_5073.JPG, 2.6 MB -
IMG_5075.JPG, 2.5 MB
-
IMG_5076.JPG, 1.2 MB
-
Replies to This Discussion
-
Permalink Reply by Dave Onastik on -
Very cool. I just got a miter saw as a gift and was wondering how to do that. I've been using my table saw for scarf joint cuts, but this looks much easier.
-
Permalink Reply by Rick on -
thanks! its very easy, just make sure to clamp the piece you are cutting to the jig as well or it may become a projectile.
-
Permalink Reply by ED (Bad Finger) on -
And I've just found it fun to free-hand it on the chop saw. :) I should take the time to make the simple guide.
-
Permalink Reply by Bluesheart on -
Yep, nice . I had a similar jig when I had a mitre saw. Saves a lot of time.
-
Permalink Reply by Rick on
-
Thanks! unfortunately, I didn't have it for my first build and I had to hack up the end of the neck for the headstock.
-
Permalink Reply by ED (Bad Finger) on
-
Nice and greasy goes down easy. Did my first one with a jig. I just used one piece of 2x4.
- Attachments:
-
-
IMAG0188.jpg, 1.4 MB
-
New CBG T-Shirt!
Sponsors
Recommended Links & Resources
- Cigar Box Music - How-to-Build CBGs DVDs, How to Play CBG and more!
- 3-String-Guitar.com
- Handmade Music Clubhouse - Dedicated to all handmade/homemade instruments
- Speal's Tavern of New Alexandria, PA - Shane Speal's Family Tavern and Cigar Box Guitar Museum
Events
Blog Posts
Albert King goes into the Rock And Roll Hall Of Fame in 2013.
Posted by RTZGUITARS on May 19, 2013 at 9:30pm 2 Comments 1 Like
New Headstock Branding
Posted by Harrison Withers on May 15, 2013 at 9:59pm 0 Comments 0 Likes
The Slim Panatellas are in Session with Emma Mitchell on The Medicine Show
Posted by The Slim Panatellas on May 15, 2013 at 6:42pm 0 Comments 0 Likes
scale length and fret placement
Posted by Harrison Withers on May 6, 2013 at 3:20pm 0 Comments 0 Likes
Ups and downs
Posted by Craig Mayhem on May 6, 2013 at 9:52am 6 Comments 3 Likes
Handmade Music Clubhouse Activity
© 2013 Created by C. B. Gitty (Ben).
Powered by
